Anti-wear Ring
(Total 5 Products)
-
Unit Price:0.02~1.01USDBrand:SPRSEALSMin. Order:1 Bag/BagsModel No:O-ring sealing back-up ringTransportation:Ocean,LandPackaging:carton,packaging bagSupply Ability:100,000 pieces per monthPlace of Origin:Jiangsu, ChinaProductivity:1 million pieces per monthThe piston rod O-ring is a sealing element commonly used in hydraulic and Pressure system. It is usually made of rubber or plastic material, with a circular cross-section and a circular hole inside for fitting onto the piston rod. The main function... -
Unit Price:0.29~1.49USDBrand:SPRSEALSMin. Order:1 Bag/BagsModel No:Bucket shaft dust ringTransportation:Ocean,LandPackaging:carton,packaging bagSupply Ability:100,000 pieces per monthPlace of Origin:Jiangsu, ChinaProductivity:1 million pieces per monthThe excavator bucket shaft oil seal refers to the oil seal on the excavator bucket shaft, which is used to prevent lubricating oil leakage and external debris from entering the interior of the bucket shaft. Oil seals are usually made of rubber or... -
Unit Price:0.53~6.28USDBrand:SPRSEALSMin. Order:1 Barrel/BarrelsModel No:CupbearerTransportation:Ocean,LandPackaging:carton,packaging bagSupply Ability:100,000 pieces per monthPlace of Origin:Jiangsu, ChinaProductivity:1 million pieces per monthOil free lubrication bearings are made of steel plates as the matrix, with spherical bronze powder sintered in the middle, A sliding bearing made by rolling a mixture of polytetrafluoroethylene (PTFE) and lead on the surface. It has the... -
Unit Price:USD 0.74 / Barrel/BarrelsBrand:SPRSEALSMin. Order:1 Barrel/BarrelsModel No:SPNTransportation:Ocean,LandPackaging:carton,packaging bagSupply Ability:100,000 pieces per monthPlace of Origin:Jiangsu, ChinaProductivity:1 million pieces per monthThe SPN seal for the excavator oil distribution cup is an important component on the excavator, mainly used to seal the excavator oil distribution cup and prevent oil leakage. Its applications mainly include the following aspects: 1. Prevention of... -
Unit Price:0.14~1.17USDBrand:Cypher SPRSEALSMin. Order:1 Barrel/BarrelsModel No:Excavator track link oil sealTransportation:Ocean,Land,Air,Express,OthersPackaging:Carton,Packaging BagSupply Ability:100,000 pieces per monthPlace of Origin:xu zhou jiangsu chinaProductivity:100,000 pieces per monthSuitable for dozer loader track idler seals floating oil seals Excavator track link oil seal is applicable to all kinds of crawler equipment, and also belongs to the category of seal repair kit, and the category of anti-wear ring is also widely...
Installation and precautions of track connecting rod oil seal
The installation steps for the track link oil seal are as follows:
1. Cleaning: Clean the connecting parts to ensure that the surface is flat, clean, and free of grease and dirt.
2. Oil application: Apply a layer of lubricating oil to the connecting parts for better installation.
3. Installation: Gently push the oil seal into the connection area to ensure that the lip of the oil seal is not damaged.
4. Positioning: After positioning the oil seal, press it with your fingers to ensure it is in the correct position.
5. Inspection: Check if the oil seal is installed correctly and ensure that the lip is not damaged.
The precautions are as follows:
Before installation, check if the oil seal is damaged. If the oil seal is damaged, replace it with a new one.
Before installation, ensure that the surface of the connecting parts is flat, clean, and free of grease and dirt.
3. When installing the oil seal, gently push in to avoid damaging the lip of the oil seal.
4. After installation, check whether the oil seal is installed correctly to ensure that the lip is not damaged.
5. During use, the condition of the oil seal should be regularly checked. If any damage or wear is found, the oil seal should be replaced in a timely manner.
Anti-wear Ring
Seal Failure cause1. Sealing design leads to failureMaterial selection (hydrolysis, chemical resistance, temperature resistance, surface velocity, etc.)Structural design (pressure, low temperature, overload, etc., such as string leakage)Gap recommendations and tolerance levelsProduct selection (single acting, double acting, pressure holding requirements, etc.)2. Sealing application leads to failure and excessive system pressureApplication temperature too high or too low (temperature resistance failure, aging)Surface roughness, oil contamination, transient wear.